This standard is issued under the fixed designation E ; the number immediately following the designation indicates the 1 This practice is under the jurisdiction of ASTM Committee E-7 on Nonde- .. Hole numbers 8 thru 12 are optional. American Society for Testing Materials ASTM-E Utilising a Fixed Line Bench12 ASTM-E and where necessary harmonises the Standard with. Hello friends, who has ASTM E? I have the version 11, don’t know the change between the two version. Thanks.

Author: Gok Maulmaran
Country: Guyana
Language: English (Spanish)
Genre: Life
Published (Last): 5 January 2005
Pages: 451
PDF File Size: 9.5 Mb
ePub File Size: 2.21 Mb
ISBN: 660-5-91079-976-5
Downloads: 50706
Price: Free* [*Free Regsitration Required]
Uploader: Mijora

You can make your ASTM selection at our website, www. Combining astm e1444-12 from the two systems may result in non-conformance with the standard. Maximum detectability occurs when the discontinuity is positioned on the surface and perpendicular astm e1444-12 the magnetic flux. Equipment According to this standard: Save my name, email, and website in this browser for the next time I comment.

That is all I have to say e1444-122 this. The required verification intervals are stated in Table 1. See Appendix X1 for additional information. Astm e1444-12 AC with 2 to 4 in. Magnetic particle testing consists of magnetizing the astm e1444-12 to be examined, applying suitably prepared magnetic particles while the area is magnetized, and subsequently interpreting and evaluating any resulting e144-12 accumulations.

New ASTM E1444/E1444M 2012 Edition – Magnetic Particle Testing

I will check them for you as soon as I have access to older versions. Hi Fyant, Welcome to ndt. Also for your information, There is another astm e1444-12 It is the responsibility of the user of astm e1444-12 standard to establish appropriate safety and health practices and determine the applicability of regulatory ashm prior to use.

This has not been changed since at least This practice establishes the astm e1444-12 parameters for controlling the application of the magnetic particle testing method. There are a total of 9 technical corrections in this release. asmt

Related Drivers  SEKINE DUASI PDF

Magnetic particle testing may be applied to raw material, billets, finished and semi-finished materials, welds, and in-service astm e1444-12. Dear Fitra, How are asstm doing? It says”Changed the existing wording in T a to clarify the required astm e1444-12 of yoke lifting power verification. I wouldn’t hesitate if knew there was something relevant inside those scrolls.

Your email address will not be published. Currently you have JavaScript disabled. If a yoke has not been in use for r1444-12 year or more, a check shall be done prior astm e1444-12 first use. I was able astm e1444-12 find the 40lb lifting force in: Or you may prefer to contact us by phonefax or email info document-center. Related Suppliers Searching for related astm e1444-12 Leave astm e1444-12 Reply Cancel reply Your email address will not be published.

Direct current yokes d1444-12 have a lifting force of at least 30 lb. EB, Did you check what the Dead Sea scrolls had to say on the subject???? Guide E can b Register or Log in for direct access to additional content.

ASTM International

Alternating current and permanent magnet yokes shall have a lifting force of at least 10 astm e1444-12. This standard practice may used for verifying lifting force daily prior to use. Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels. It is not a detailed astm e1444-12 procedure to be used by the examination personnel and, therefore, must be supplemented by a detailed written procedure that conforms astm e1444-12 the requirements of this practice.

According to the latest version of the standard, AC Yokes must be able to lift 10 lb 4. Alternating current and permanent magnet yokes shall have a lifting force of at least 10 astm e1444-12 [4. Guide E can be astm e1444-12 in conjunction e4144-12 this practice as a tutorial.

This standard has been updated more regularly there are 24 older versions before and I do not have access e1444-112 older version. Direct current yokes shall have a lifting force of at least 30 lb Nastm e1444-12 a 2 to 4-in. Magnetization shall be determined by astm e1444-12 the tangential field strength, Ht, at the centre of a line joining the astm e1444-12 of the pole faces of the electromagnet with pole extenders where used.

Related Drivers  DELL XPS M140 MANUAL EBOOK

The electromagnet shall be capable of supporting a steel plate or rectangular bar conforming to C22 1.

New ASTM E/EM Edition – Magnetic Particle Testing – Document Center’s Standards Forum

This adtm is written so that it can be specified on the engineering drawing, specification, or contract. The atsm power of all yokes shall be checked whenever the yoke has been damaged or repaired. Link to Active This link will always route to the current Active version of the standard. Lifting force according to ASME sec. This standard practice may used for verifying lifting force every 6 month related in publishing the calibration certificate.

V article 7, para T So you will need a 40lbf lifting force for DC current electromagnetic yokes with pole spacing of 3 to 6 inch astm e1444-12 you want to carry out MPI testing on Steel Forgings.

You can see this astm e1444-12 the “List of changes in record number order” section, number You can see the complete history of the standard at our astm e1444-12 revision history astm e1444-12 available for every standard on our website.

Click here for instructions on how to enable JavaScript in your astm e1444-12. I knew that I saw that somewhere. And hasn’t changed ever since. Work Item s – proposed revisions of this standard.